欢迎访问2022世界杯下注平台有限公司网站!

热线:400-893-8887

掌握切菜机操作流程确保自身安全

来源:http://www.carnetsdecharme.com/ 浏览量: 时间:2022-07-23 11:50:09

大型切菜机的使用,用户操作简单、方便、安全。更重要的是,切菜速度快,效率高,并且保证切菜的质量,不过,注意的是,切菜机虽然操作简单方便,但是用户也要了解并掌握切菜机操作流程,确保设备使用安全。
The use of large vegetable cutting machine is simple, convenient and safe for users. More importantly, the cutting speed is fast, the efficiency is high, and the quality of the cutting is guaranteed. However, it should be noted that although the cutting machine is simple and convenient to operate, users should also understand and master the operation process of the cutting machine to ensure the safety of the equipment.
机械启动前,要检查防护设备和电源以及各零件是否完好,刀具是否锋利以及是否存在硬物和异物等。如有异物必须清理干净,以免造成刀具损坏。与此同时,操作前将设备放置在水平地面,保障机器放置平稳可靠。
Before starting the machine, check whether the protective equipment, power supply and parts are in good condition, whether the knives are sharp, and whether there are hard objects and foreign objects. If there is any foreign matter, it must be cleaned to avoid tool damage. At the same time, place the equipment on the level ground before operation to ensure that the machine is placed stably and reliably.
确定设备插头接触良好,无松动,无水迹。并对切菜机的切菜刀片、设备内部、托盘及传输带进行彻底清洗消毒,避免物料受到污染,保障产品安全、卫生。之后,便可以启动,但是切勿急忙投入物料。好使设备空转2分钟左右,待运行一切正常便可以进行投料工作。
Make sure that the plug of the equipment is in good contact without looseness or water trace. And thoroughly clean and disinfect the vegetable cutting blade, equipment interior, tray and transmission belt of the vegetable cutting machine to avoid material pollution and ensure product safety and hygiene. After that, it can be started, but do not rush into materials. In order to make the equipment idle for about 2 minutes, the feeding work can be carried out after everything is normal.
用户投料有讲究,并不是投料越快越好,或者越多越好,要保证投料均匀,避免物料堵塞切菜机造成设备停机或者出现故障。如若出现堵塞要停机,及时进行清理,确保设备安全运行。
Users pay attention to feeding. It's not that the faster the feeding is, the better, or the more the better. It's necessary to ensure that the feeding is uniform, so as to avoid blocking the vegetable cutting machine and causing equipment downtime or failure. In case of blockage, stop the machine and clean it in time to ensure the safe operation of the equipment.
值得注意的是,投料前要根据物料特点和工艺需要调节好切割模式。通常竖刀模式可将叶类软菜或切好的片加工成不同规格的丁、块、丝、菱形等各种形状。
It is worth noting that the cutting mode should be adjusted according to the material characteristics and process needs before feeding. Usually, the vertical knife mode can process leaf soft vegetables or cut pieces into various shapes such as Ding, Kuai, Si, diamond, etc. with different specifications.
大型切菜机
用户安装竖刀需要注意事项。先转动可调偏心轮,移动刀架至无法移动位置,再使刀架上抬1-2mm。当竖刀与输送带接触,固定螺母,把竖刀紧固在刀架上。倘若刀架抬起高度较小,刀具上粘上物料较多。如果刀架抬起高度太大,有可能对输送带造成损坏。为此,用户在调节切刀时一定要格外把控好调节高度。
Precautions for users to install vertical knives. First turn the adjustable eccentric, move the tool holder to the position where it cannot be moved, and then lift the tool holder up by 1-2mm. When the vertical knife contacts with the conveyor belt, fix the nut and fasten the vertical knife on the knife rest. If the lifting height of the tool holder is small, more materials are stuck to the tool. If the tool holder is raised too high, it may cause damage to the conveyor belt. For this reason, the user must control the adjustment height when adjusting the cutter.
大型切菜机设备运行中,用户要查看物料切割的规格是否符合要求。若是不符合工艺需要,要及时停机,调整相应的切割参数,做到规格统一,避免切菜效果不符合要求而造成物料不必要的浪费。
During the operation of large-scale vegetable cutting machine, users should check whether the cutting specifications of materials meet the requirements. If it does not meet the needs of the process, it is necessary to stop the machine in time, adjust the corresponding cutting parameters, and achieve unified specifications, so as to avoid unnecessary waste of materials caused by the unqualified cutting effect.
用户要关好传输系统和刀片上的安全保护装置。物料加工完成后,要及时按下控制系统的停止按钮,并关闭控制电源。为了避免设备二次使用污染物料,每次完工后都需要对切菜机进行维护、清洗。更多关于该设备的相关事项就来网站http://www.carnetsdecharme.com咨询了解吧!
Users should turn off the safety protection devices on the transmission system and blade. After the material processing is completed, press the stop button of the control system in time and turn off the control power. In order to avoid the secondary use of polluting materials, the vegetable cutting machine needs to be maintained and cleaned after each completion. For more information about the device, please visit the website http://www.carnetsdecharme.com Consult and understand!

备案号:京ICP备13030550号-2